Results 1 to 2 of 2
  1. #1
    Join Date
    Nov 2005
    Location
    Scottsville, Virginia
    Posts
    1,104

    Default Tweaking Guider FOVi

    I'm trying to get some info from MaxIm because in one of their updates some time ago they changed the active star detection area, for lack of a better term, for the guide chip. It went from some unknown boundary to a new smaller boundary where the guide star will be detected by MaxIm. Seems it use to be small like maybe 5 pixels. By boundary I mean like an invisible rectangle that the guide star must be in before MaxIm will see and use it. I use to calibrate by picking a star at a PA0, east of the meridian, and as close to DEC 0 as possible. I'd position my guide star in the far upper left corner because the calibration for me would move the star from the upper left across to the right, back again , and then down, and back. I set both my move times (X & Y) to move the star as far as I could down (Y) without going off the chip. This was done to run out any possible backlash and usually gave a very accurate calibration that would not be changed for years short of a change in equipment.

    Now that active guide window has shrunk and I can't seem to find the dimensions so I can draw a inner rectangle to be sure the star is usable. Of course center is ideal but not always possible when framing the target. The issue comes into play when your guiding is set to dither. I've had a series start and get multiple images but with the dither set to -1 in Scheduler targets I have no idea which way or how much that star may move and I'm suspecting that it may be enough at times to move it out of the active area of the usable guider chip. What I'm saying is I think it's possible to have multiple guiding failures of the same target that you may already have some images taken of and not have any idea why unless you stay up all night and watch the process.

    Now maybe I need to get a better understanding on how dithering works so I can control this better and not accidently go outside the active detection area of the guide chip or not use the dithering option when setting targets up. I usually have large sets of data to process so the combine methods would take care of the outlier artifacts I would think. But it would be good to understand this better and use the best method.
    Steve
    http://www.astral-imaging.com

    Scottsville, Virginia
    ACP Expert
    AP1200GTO
    Tak EM200
    AP 92mm Stowaway
    OGS 12.5" RC
    TAK FSQ-106ED
    STL-11000M/CF8
    ST10XME/CFW8
    Pyxis 3" Rotator

  2. #2
    Join Date
    Oct 2005
    Location
    Mesa, AZ
    Posts
    27,913

    Default

    As shipped (default), dithering units in ACP are in guider pixels, so it's easy to tell how far it will move. If you put the guider plate scale in arcsec/pic into ACP then it will dither in main image pixels. Some people prefer this. The number you give is a sort of an average, but each dither is random in X and Y. If you put lets say 5 in there, it will dither up to maybe 8-10 pixels, which is way smaller than the guide sensor dimensions.

    You can get the guider plate scale given the guider's pixel size in microns and the focal length (use the focal length that is measured, taken from an ACP observing log), then going to this online calculator:

    https://astronomy.tools/calculators/ccd
    -- Bob

 

 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Relating TheSkyX FOVI angle to sky PA
    By Dan Simpson in forum Hardware/Software/Driver Topics Not Directly Related to Our Software
    Replies: 1
    Last Post: Mar 10, 2018, 15:55

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •