Member login
Activity Stream
-
Older Activity
-
Yesterday, 20:56Bob Denny replied to a thread MaxIm DL Pro 6.21 released 2020-01-16 in Add-Ons, Enhancements, and Helper ComponentsOK, then this has been moved to the MaxIm forum. Thanks guys.9 replies | 121 view(s)
-
Yesterday, 19:37Colin Haig replied to a thread MaxIm DL Pro 6.21 released 2020-01-16 in Add-Ons, Enhancements, and Helper ComponentsWilliam - we do appreciate you bringing it up, but the best place is over in the other side so that we can get to the root cause. Here's what I...9 replies | 121 view(s) -
Yesterday, 19:22William Bristow replied to a thread MaxIm DL Pro 6.21 released 2020-01-16 in Add-Ons, Enhancements, and Helper ComponentsColin. If you read my first post in the thread you will see that the error has been reported by another MaxIm user on the Diffraction Forum, I see...9 replies | 121 view(s)
-
Yesterday, 19:18Colin Haig replied to a thread MaxIm DL Pro 6.21 released 2020-01-16 in Add-Ons, Enhancements, and Helper ComponentsIf you have a reproducible test case, please report this issue on the Diffraction Limited forum. We have no evidence of such a problem at this time,...9 replies | 121 view(s)
-
Yesterday, 19:15William Bristow replied to a thread MaxIm DL Pro 6.21 released 2020-01-16 in Add-Ons, Enhancements, and Helper ComponentsThanks Dick. I will see how much is salvageable when I get back home at the weekend. Most of my planned ACP runs were terminated early by the...9 replies | 121 view(s)
-
Yesterday, 18:57Bob Denny replied to a thread MaxIm DL Pro 6.21 released 2020-01-16 in Add-Ons, Enhancements, and Helper ComponentsEek! I just tested MaxIm 6.21 and the FITS headers I am getting a good Date-Obs, e.g.: DATE-OBS = '2020-01-23T18:38:10.95' /YYYY-MM-DDThh:mm:ss...9 replies | 121 view(s)
-
Yesterday, 18:37Albert van Duin replied to a thread GEM flip with Sitech controller in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareHello Bob, Thanks for discussing this with Dan Gray. I will try these settings as soon as the weather cooperates, and I will post my findings...11 replies | 287 view(s)
-
Yesterday, 17:17Dick Berg replied to a thread MaxIm DL Pro 6.21 released 2020-01-16 in Add-Ons, Enhancements, and Helper ComponentsWilliam, Too, too bad, but depending on how much value you put on the lost observations, using the ACP run logs you could use MaxIm to edit the FITS...9 replies | 121 view(s)
-
Yesterday, 16:56William Bristow replied to a thread MaxIm DL Pro 6.21 released 2020-01-16 in Add-Ons, Enhancements, and Helper ComponentsImportant !!! There is a FITS header bug in the MaxIm DL 6.21 release that may cause corrupted image data with some camera drivers. If you...9 replies | 121 view(s)
-
Yesterday, 16:31Bob Denny replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareThe completion state numbers allow starting from the next image count/repeat/set without starting a set over. I understand but I will stay with it as...40 replies | 517 view(s)
-
Yesterday, 14:23Arto Oksanen replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareThis brings up another "issue". This version of ACP writes #completionstate in the plan file and does not increase the set number if the run was...40 replies | 517 view(s)
-
Yesterday, 14:08Arto Oksanen replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareI was processing the images while this "daytimetest" was running. It is not what is usually done, and I remember that there was one image that was...40 replies | 517 view(s)
-
Yesterday, 12:53Bob Denny replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareThis looks very encouraging! The logs appear flawless. I can see it getting light out at around 0540 UTC ha ha.40 replies | 517 view(s)
-
Yesterday, 12:52Bob Denny replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareI see the long wait at 0649 UTC. It almost hit the T + 120 second failure timer. ALso one that ran 15 seconds a bit later, but the rest of the images...40 replies | 517 view(s)
-
Yesterday, 11:00Arto Oksanen replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareHere is the log file from the daytimetest. No errors, but one wait was very long. I was using MaxImDL interactively at this time (platesolving...40 replies | 517 view(s)
-
Yesterday, 06:32Arto Oksanen replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareHere are the log files from the first night with the new software. No looping and everything seemed to work perfectly. I will run also the daytime...40 replies | 517 view(s)
-
Jan 22, 2020, 19:07Bob Denny replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareOK, thank you. If you have trouble seeing new posts in the thread tree (and I do sometimes!) you can switch to Linear mode and the newest posts will...40 replies | 517 view(s)
-
Jan 22, 2020, 18:39Arto Oksanen replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareI found it now. It seem to be very easy to miss posts on the forum. I could have tried it yesterday. Now it is again cloudy, but I will install...40 replies | 517 view(s)
-
Jan 22, 2020, 18:16Bob Denny replied to a thread Camera Hangs and Stops Plan in Hardware/Software/Driver Topics Not Directly Related to Our SoftwareNo that's not it. Keep in mind that only you and SDAA have seen the problem. Have you tried the new AcquireSupport?40 replies | 517 view(s)
Powered by vBulletin® Version 4.2.4
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.
All times are GMT. The time now is 00:06.
vBulletin 4.0 skin by CompleteVB
